Sensaphone 2800

Sensaphone 2800

Now you can monitor critical conditions at remote locations without running wires, Introducing the new Sensaphone 2800 with wireless Sensor Technology. Based on proven Sensaphone remote monitoring methods, the 2800 adds the ability to read sensor status from wireless sensors.

And not just simple on/off status, or open/closed conditions. The Sensaphone Wireless Technology includes full analog capability so real world values
can be monitored, like actual temperatures,
real tank levels and flow rates.

In addition to the wireless sensors, there are also two Wireless Interface modules. These allow you to connect to existing equipment or sensors and transmit their status back to the 2800 wirelessly. There is a Dry Contact wireless module, and even a 4-20mA wireless module. The 4-20mA wireless module even provides battery backed 24 VDC loop power for your transducer.

Stick It Anywhere!

Most of the Sensaphone Wireless Sensors run on batteries for up to 3 years. You can literally, just stick a sensor to the wall and start monitoring right away. The 2800 will scan, find the sensor, self configure and do most of the work for you. All you need to do is to record a custom voice message and fill in a few parameters.

Self Diagnostics

The Wireless Sensor Network is always being watched by the 2800. In addition to looking for alarms from the sensor values, it is also looking to make sure that each wireless sensor is fully functional and its batteries are full. If there are any problems with the wireless sensors, the 2800 will initiate a diagnostic alarm and notify the appropriate personnel immediately.

Notification: Just like the other Sensaphone products, the 2800 uses the reliability of a standard phone line to make phone calls to the appropriate personnel to announce alarm conditions. Each monitoring condition, both wired and wireless, can have custom voice message attached to it. Each message is recorded in your own voice for easy identification. Alarm notification will repeat out to eight people until acknowledged.

Applications: Use the 2800 to monitor multiple greenhouses without wires, multiple barns, coolers, freezers, or a wide variety of remote equipment. The new Sensaphone 2800 can be used anywhere you would use our other Sensaphone products. The 2800 just makes installation and expansion faster and easier. Extend your reach and monitor your critical remote locations with the new Sensaphone 2800.

Available Wireless Sensors

Wireless Temperature Sensor:
Can be wall mounted with screws or double-sided foam tape. Measures temperature from 32° F to 115° F
( 0° C to 57° C). Adding FGD-0101 temp sensor extends range down to -109° F (-85° C) Includes AAA batteries that will run for approx. 3 years. Optional AC adapter so batteries are only used during power failure..........WSR-0100

Wireless Dry Contact Sensor:
Can be wall mounted with screws or double-sided foam tape. For Normally Open or Normally Closed contacts. Includes 3AAA batteries that will run for approx. 3 years Optional AC adapter so that the batteries are only used during power failure..........WSR-0101

Wireless Power Failure Sensor:
Can be wall mounted with screws or double-sided foam tape. Comes with AC adaptor for sensing power failure. Monitors power failure from where ever the AC adapter is plugged into. Includes 3 AAA batteries to operate during power failure..........WSR-0102

Wireless Humidity Sensor:
Can be wall mounted with screws or double-sided foam tape. Measure humidity from 0 to 100% RH. Includes 3 AAA batteries that will run for approx. 3 years. Optional AC adapter so that batteries are only used during power failure..........WSR-0103

Wireless 4-20mA Sensor:
Can be wall mounted with screws or double-sided foam tape. Works with any 4-20mA transducer. Custom table range so monitoring is in real engineering units. Built-in 24 volt power supply for providing 4-20mA loop power. Includes AC adapter. Also includes 3 AAA batteries for full operation during a power failure..........WSR-0104

Wireless Motion Detector:
Can be wall mounted with screws or double-sided foam tape. Detects movement in a specific area for unauthorized entry or intrusion. Includes 3 AA batteries that will run for approx. 3 years..........WSR-0105

Wireless Spot Water Detection Sensor:
Detects the presence of water in a floor or in a false ceiling. Comes with 10 feet of water rope to cover a larger area Includes 3AAA batteries that will run for approx. 3 years..........WSR-0106

Wireless Zone Water Detection Sensor:
Detects the presence of water on a floor or in a false ceiling. Comes with 10 feet of water rope to cover a larger area than WSR-0106. Includes 3 AA batteries that will run for approx. 3 years. Optional AC adapter so that batteries are only used during power failure..........WSR-0107

Wireless Repeater:
Can be wall mounted with screws or double-sided foam tape. Extends wireless sensor range up to one mile line-of-site. Includes AC adapter. Also includes 3 AAA batteries for full operation during a power failure..........WSR-0199